Vodavi Triad-S 1-2-3 Single Line Installation Manual Page 178
- Page / 236
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Station Connections 3-75
Single Line Interface Board (SLIB)
This board providesthe interface to twelve (12) 2500-type telephones.
The SLIB signals interface with mechanical 90V ringers and lights 90V
messagewaitinglampson2500setsasdesired.TheSLIBboardhasone
LED indica tor for status . A Norma l/Service sw itch located towa rd th e top
of the card allows the card to be inserted or removed from the system
while under power and also can be used to disable all station circuits on
the ca rd.
The station connections are via one (1) 50-pin female (amphenol type)
connector located on the front edge of the card.
The board can support a MSG12 board and a DTMF4-A board in a
daughter board type arrangement.
The MessageWait Lamp Relay Control (MSG12) provides Message Wait
Lamp Relay Control for message la mp s ingle line tele phones. The MSG12
board m ounts on the SLIB board as a daughter board type arrangement.
Installing the MSG12 Board
1. Unpack theMSG12 Module from its anti-static conductive bag in the
packing box.
2. Locate the CONN5 and CONN6 connectors on the MSG12 module.
3. Locate the CONN3, and CONN4 connectors on the SLIB (outlined).
4. Position theMSG12 module so that the CONN3 and CONN4
connectors match up with the CONN3 and CONN4 connectors on the
SLIB respectively.
5. PushtheMSG12moduleontotheseconnectorsmakingsureitis
seated properly.
Refer to Figure 3-27. This completes the installation procedure for the
MSG12 Module.
- Installation 1
- STARPLUS 2
- Triad 1/2/3 2
- Contents 4
- 3 Triad 3 System Installation 5
- 4SystemCheck-Out 7
- March 20 01 v 8
- March 20 01 viii 11
- March 20 01 xi 14
- Telephone Numbers 18
- Triad 1/2 Systems Information 18
- Triad 3 System Information 18
- FCC Registration Numbers 18
- Incidence of Harm 19
- Changes in Service 19
- Maintenance Limitations 19
- Hearing Aid Compatibility 19
- UL/CSA Safety Compliance 19
- Notice of Compliance 20
- 1-6 Toll Fraud Disclaimer 21
- Triad 1/2 System 22
- Powe r Line Surge Protection 42
- PCB Installation 2-23 44
- Figure 2-11: PCB Installation 44
- Removing Existing Software 46
- Installing Ne w Software 46
- Modem Unit (MODU) 48
- CO/PBX Connections 2-35 56
- DID Interface Board (DIDB) 57
- CO/PBX Connections 2-51 72
- CO/PBX Connections 2-55 76
- 2-56 CO/PBX Connections 77
- Station Connections 2-59 80
- Installing the DTRU Module 82
- Installing the MSGU Board 82
- 2-64 Station Connections 85
- 2-66 Station Connections 87
- System Wiring 88
- MISU Wiring 90
- ICLID Cable Pin-Out Diagram 97
- RJ45/DB9/RS232 97
- Figure 2-35:SMDR Printout 101
- Figure 2-32:SMDR Printout 102
- Triad 3 System 104
- Introduction 106
- Site Preparation 106
- Back-Board Installation 107
- Verify On-Site Equipment 108
- 3-6 Site Preparation 109
- Mounting the Basic KSU 110
- KSU Grounding 115
- BKSU Front View 116
- AC/DC (PS-10A or PS-15A) 117
- DC/DC (with BCU & 48VU) 119
- Power Line Surge Protection 129
- Lightning Protection 129
- KSU AC Power Plug 129
- PCB Installation 130
- Removing a PCB 131
- Serial Interface Unit (SIU2) 134
- Phase Lock Loop Unit (PLLU) 135
- Memory Expansion Unit (MEMU) 136
- Program Module Unit (PMU) 136
- Installing the PF TU 140
- CO/PBX Connections 143
- 3-42 CO/PBX Connections 145
- Installing the DTMF-B Module 146
- CO/PBX Connections 3-45 148
- DID Trunk Board (DIDB) 149
- 3-48 CO/PBX Connections 151
- Functionality Description 154
- Installing the DTMF-A Modules 159
- CO/PBX Connections 3-57 160
- CO/PBX Connections 3-63 166
- CO/PBX Connections 3-65 168
- 3-66 CO/PBX Connections 169
- CO/PBX Connections 3-67 170
- ISDN and T1 Clocking 171
- 3-70 CO/PBX Connections 173
- T1IB1 T1IB2 T1IB3 PRIB1 PRIB2 173
- Statio n Conn ections 175
- 3-74 Station Connections 177
- Installing the MSG12 Board 178
- Adjusting Modem Sett ings 179
- Installing the DTMF-A Unit 181
- Station Connections 3-79 182
- 3-80 Station Connections 183
- Station Connections 3-81 184
- Station Connections 3-83 186
- Station Wiring 187
- Station Wiring 3-85 188
- Single Line Telephone Wiring 189
- Power Failure TransferWiring 190
- Headset Installation 193
- Programming the KSU 195
- Figure 3-38:SMDR Printout 198
- Figure 3-36:SMDR Printout 199
- System Check-Out 200
- Preliminary Procedures 202
- Powe r Up Sequence 202
- Maintenance and 204
- Troubleshooting 204
- Keyset Self Test 207
- Keyset LCD/LED Test 208
- Keyset Button Test 208
- DSS LED/Button Test 209
- Key Telephones/Terminals 210
- Single Line Telephones 211
- DSS/DLS Console 211
- CO Line Card Functions 212
- System Function s 214
- Miscellaneous Functions 217
- Station Card Functions 218
- Remote Maintenance 219
- Exit Maintenance 220
- System Configuration 221
- Station Configuration 221
- CO Line Configuration 223
- Event Trace Buffer 224
- Remote System Monitor 225
- Monitor Password 226
- Help Menu (?) 226
- Event Trace Mode 227
- Dump Memory Data 227
- Remote System Monitor 5-25 228
- Modify Memory Command 229
- Baud Rate Command 230
- Exit the Monitor Mode 230
- 5-28 Remote System Monitor 231
- March 20 01 iii 234
- ©2000 Vodavi Technology,Inc 236
Related products and manuals for Telephones Vodavi Triad-S 1-2-3 Single Line
Telephones Vodavi WIT-300H Specifications
(139 pages)
(139 pages)
Telephones Vodavi 3551-00 User's Guide
(118 pages)
(118 pages)
Telephones Vodavi Digital Telephone User's Guide
(122 pages)
(122 pages)
Telephones Vodavi Starplus DHS-L User's Guide
(108 pages)
(108 pages)
© 2020, manymanuals.com. All rights reserved. | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals